If you are
trying to get signal from a Ku band DSS Circular & FSS Linear
satellites for FTA and have a DiSEqC1.2 compatible or USALS
compatible FTA Ku band receiver, then go with
Motorized Dish Kit #3. This package will allow the
reception of both linear and circular signals broadcasting from
almost any Free To Air FTA satellite.
Click Here
Channel List
If you
only want to be able to receive standard Ku band signal from almost
any FTA satellite and have a DiSEqC1.2 compatible or USALS
compatible FTA receiver, then you need the
Motorized FTA Dish Kit #4. This package allows reception
of only FSS linear Ku band satellite signal broadcasting from almost
any FTA Ku band satellite.
Click Here
for Channel List
This
package is just like the FTA Motorized Dish Kit #4 above, but
includes a 1.2m / 120cm offset dish antenna rather than a 76cm /
.76m offset dish. If you only want to be able to receive
standard Ku band signal from almost any FTA satellite and have a
DiSEqC1.2 compatible or USALS compatible FTA receiver and live in a
fringe area or want to point to a low powered satellite, then you
need the
Motorized FTA Dish Kit #5. This package allows reception
of only FSS linear Ku band satellite signal broadcasting from almost
any FTA Ku band satellite.
Click Here
for Channel List
This
package is just like the FTA Motorized Dish kit #3 above, but
includes a 120cm / 1.2m offset dish antenna rather than a 75cm /
.75m offset dish. If you are trying to get signal from a Ku
band DSS Circular & FSS Linear satellites for FTA and have a
DiSEqC1.2 compatible or USALS compatible FTA Ku band receiver, and
live in a fringe area or if you want to get signal from a low
powered satellite, then go with
FTA Motorized Dish Kit #6. This package will allow the
reception of both linear and circular signals broadcasting from
almost any Free To Air FTA satellite.
Click Here
Channel List
This
package is just like the FTA Motorized Dish kit #3 above, but
includes a 90cm / .9 meter offset dish antenna rather than a 75cm /
.75m offset dish. If you are trying to get signal from a Ku
band DSS Circular & FSS Linear satellites for FTA and have a
DiSEqC1.2 compatible or USALS compatible FTA Ku band receiver, and
live in a fringe area or if you want to get signal from a low
powered satellite, then go with
Motorized
FTA Dish Kit #7. This package will allow the
reception of both linear and circular signals broadcasting from
almost any Free To Air FTA satellite.
Click Here
Channel List
Do you get
low signal? Try this Kit. This is just like the
Motorized FTA Dish Kit #4, but includes a
90 centimeter dish instead of a
76 centimeter FTA dish. If you
only want to be able to receive standard Ku band signal from almost
any FTA satellite and have a DiSEqC1.2 compatible or USALS
compatible FTA receiver, then you need the
Motorized FTA Dish Kit #8. This package allows reception
of only FSS linear Ku band satellite signal broadcasting from almost
any FTA Ku band satellite.
Click Here
for Channel List
FAQ about Motorized Satellite Systems:
Do I need
to install a separate power line to connect to the
HH motor mount?
-
No. The
motor gets powered by the receiver. The receiver provides power to
turn the LNB on and to switch polarity. The motor consumes the
same power through the
coaxial cable that runs from the receiver to the
LNBF. Simply run the coaxial cable to your satellite dish motor,
then from the HH dish motor run a 3 or 4 foot coaxial cable to the LNBF.
How do I
control the motor to move it East / West?
-
The motor is
controlled by the receiver's remote control. All receivers compliant
with the DiSEqC 1.2, 1.3, or USALS protocol have the capability to run
an HH
satellite motor. Once you install and setup the motor to follow the
satellite arch properly and store the different satellite positions and
locations into the receiver, the receiver will automatically go to the
location where the channel is being broadcasted from when you change TV
channels on the receiver.
Are all
HH motors & receivers USALS,
DiSEqC 1.2, & DiSEqC 1.3 compatible?
-
No.
All satellite motors and HH mounts are DiSEqC1.2 & DiSEqC1.3 compatible,
but not all
dish motors are USALS compatible. Motors that are NOT
USALS compatible are sometimes more reliable.
-
-
Not all
satellite C/Ku band receivers are DiSEqC 1.2 and DiSEqC 1.3 compatible.
Some are
DiSEqC1.0. Make sure the receiver
you purchase is at least DiSEqC 1.2 compatible.
Can I
pick up
C band and Ku band?
-
No. You need a C band dish (2.4 meters / 6 foot) or
larger to be able to pick up C band. This system is
only for Ku band reception.
Does the
motor also adjust for variation in elevation on the dish for each and
every satellite
Yes.
When you install the motor based on your latitude, the motor will adjust
the elevation as well.
Should I
skew (rotate) my
LNBF to align for polarity?
No. Just
leave the LNB at 0 degrees skew and the motor will tilt the satellite
dish to make up for the adjustment of skew.
What is
the benefit from motorizing my dish?
- Adding a
motor to your system allows you to receive satellite channels from
multiple satellites & not just one.
View
Cart
